The Best Dishwasher Side Mounting Brackets

Product Description

Allows mounting of dishwasher to side of cabinet.

From the Manufacturer

Allows mounting of dishwasher to side of cabinet.

Installation Directions
1.) Turn off power to your dishwasher in breaker box
(ABSOLUTELY CRITICAL TO AVOID SHOCK)
2.) Rotate lower access panel fasteners and remove them
3.) Remove access panel/sound dampening pad. Determine if the water supply
or power lines have enough slack to move the dishwasher. If not, you will need to
turn off water supply valve, disconnect water supply line from inlet valve & release
power line from junction box
4.) Open dishwasher door, remove the screws from the existing brackets (if present)
5.) You will next be moving the dishwasher. To do so, you may need to lower the
dishwasher by adjusting the leveling legs
6.) Carefully pull dishwasher a few inches away from the front of the cabinet
7.) Use pliers to pull up tabs in back of the bracket (if present). Pull out old brackets
8.) Insert new brackets. Use pliers to adjust the back tab to lock the brackets in place
9.) Slide the dishwasher back into the cabinet (readjusting the leveling legs, if necessary).
Replace the screws in your new brackets
10.) Reverse steps 3, 2 and 1.

This is a generic product manufactured and distributed by Impresa Products
This is not a Whirlpool, Sears, Kenmore, Amana, Jenn-Air, Crosley, Maytag
Roper, Magic Chef, Estateor Inglis OEM product and Impresa Products has no affiliation
with or endorsement from these brands. Our product is not covered under any
other manufacturer’s warranty (except for Impresa Products). The Whirlpool,
Sears, Kenmore, Amana, Jenn-Air, Crosley, Maytag, Roper, Magic Chef,
brand names and logos are the registered trademarks of their owners.
Any use of the Whirlpool, Sears, Kenmore, Amana, Jenn-Air, Crosley, Maytag,
Roper, Magic Chef model or any other related
designations are made solely for purposes of description.

The Dishwasher Under-Counter Bracket secures the dishwasher to the counter top. If your appliance’s bracket is broken or missing, you can easily replace it with this part. This accessory is designed for use with granite counter tops or other solid surfaces, new or existing, and with all stainless and plastic tall tub platforms. This part includes (1) bracket, (6) mounting screws and installation instructions. This is an accessory that can be used across several brands; check to see if your model number is compatible. Installing this part will require basic hand tools, some disassembly of the dishwasher and novice repair experience. You must unplug the dishwasher or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the water supply under the sink.

TESTED, TRUSTED AND BACKED BY OUR TOP-RATED WARRANTY AND CUSTOMER SERVICE!

1) Turn off power to dishwasher in breaker box (ABSOLUTELY CRITICAL TO AVOID SHOCK), turn off water supply. 2) Pull dishwasher out from its place. 3) Remove upper screw from side of dishwasher. Align last hole of bracket on long flat part of bracket with screw hole. Reinsert & tighten removed screw / one new provided screws. 4) Push dishwasher back into place. Open door. Determine which bracket hole to use. You want to use the farthest hole forward that still attaches to cabinet. If using holes on the smaller flat part of bracket, see 5A-6A. If using back hole, see 5B-9B. 5A) If using front hole, leave bracket as is. If using 2nd hole, use 1 pair of pliers to hold bracket at the 2nd hole & 1 pair of pliers to break off front tab. Repeat. Push dishwasher into place. 6A) Pre-drill screw holes to avoid splitting wood. Screw brackets into place using provided screws. DONE! 5B) If you cannot use either of front two holes on bracket, you will need to drill a hole in tub. Use sharpie to mark through back bracket hole on dishwasher. Repeat. Remove both brackets. 6B) Using 2 sets of pliers, break off both brackets before bend. 7B) Drill 3/8 in hole through each side of plastic tub. Hold plastic tightly right below mark & use a drill slowly to ensure you have a clean hole without damaging tub. Clean up both holes with razor blade until smooth. 8B) Put brackets back on, put dishwasher back into place. Pre-drill small holes into cabinet wood, then screw in included screws on each side. 9B) Insert plastic plugs in each hole. Run dishwasher & check for leaks. If leaks are present, you may need to add rubber cement to plastic plugs to create a seal.

This is a generic product manufactured & dist. by Impresa Products (TM). This is not an OEM product. Any use of brand names, models, etc. is made solely to describe & illustrate compatibility.

Fit Whirlpool dishwasher perfectly, do a great job of securing the dishwasher.
If your dishwasher is not mounted to the side of the cabinet or the floor, these brackets should be added to prevent it from tipping forward when you are loading it or from vibrating during use.

8212560 Dishwasher side mounting bracket:
Replaces part numbers: 1201084, AP3953705
8269145 Dishwasher upper mounting bracket:
Replaces part numbers: WP8269145, WP8269145VP

PACKAGE LIST: 

2 x 8212560 dishwasher side mounting bracket
  4 x black installation screws
  2 x 8269145 dishwasher upper mounting bracket
  2 x silver installation screws

Practical to use: 
Compatible with various brands such as Whirlpool, May-tag, Ken-more, Amana, Cros-ley, Estate, Inglis, Jenn Air, Kitchen-Aid, Magic Chef, Roper. 

This is an authorized aftermarket product. Fits with various Bosch Brand models. It has a OEM Part # 00628371.

Replaces the following part numbers:
WP8269145, WP8269145VP.

Works for brands:
KitchenAid, Whirlpool, Kenmore, Maytag, Jenn-Air, Amana, Estate, Magic Chef, Inglis, Crosley, Roper.

Fixes problem with:
Door latch failure.
Door won’t close.

Contact Us
If you are not sure if part is correct, ask us in Customer questions & answers section or contact us by visiting the Discount Parts Direct storefront.

Business Wholesale
We are a small local company from Houston, Texas offer discount parts for retail and wholesale. If you need to purchase parts for business , please contact us for lower rates.

Genuine Original Equipment Manufacturer (OEM) parts! This mounting bracket kit (part number 00619985) is for dishwashers. Mounting bracket kit 00619985 secures the dishwasher to the counter. Unplug the dishwasher or shut off the house circuit breaker before installing this part. Wear work gloves to protect your hands. For Bosch & Thermador.